- 您现在的位置：买卖IC网 > Sheet目录242 > PFE850-12-054RA (Power-One)FRONT END 850W 12V HI EFFICIENCY
DATA SHEET
If a power supply is in a fault condition, it will pull low its active-high HOTSTANDBYEN_H pin which indicates to the other
power supply that it is not allowed to enter the hot-standby mode or that it needs to return to normal operation should it al-
ready have been in the hot-standby mode.
NOTE : The system controller needs to ensure that only one of the power supplies is allowed to enter the hot-standby model.
Figure 31 shows the achievable power loss savings when using the hot-standby mode operation. A total power loss reduc-
tion of 45% is achievable.
Figure 30 - Hot-standby enable/disable current thresholds
2 PSU on
1 PSU on
Figure 31 - PSU power losses with/without hot-standby mode
60
50
40
30
20
Total
System
10
Hot-Standby Disabled
Hot-Standby Enabled
36A 45A
90A
Current
0
0
100
200
300
400
500
600
700
800
Po [W]
Figure 32 - Recommended hot-standby configuration
PSU 1
VSB
CS
HOTSTANDBYEN
PRESENT_L
3 x 3k3
PSU 2
VSB
CS
HOTSTANDBYEN
PRESENT_L
In order to prevent voltage dips when the active power supply is unplugged while the other is in hot-standby mode, it is
strongly recommended to add the external circuit as shown in Figure 32. If the PRESENT_L pin status needs also to be read
by the system controller, it is recommended to exchange the bipolar transistors with small signal MOS transistors or with
digital transistors.
8.12 I 2 C / SMBUS COMMUNICATION
The interface driver in the PFE supply is referenced to the V 1 Return. The PFE supply is a communication Slave device only;
it never initiates messages on the I 2 C/SMBus by itself. The communication bus voltage and timing is defined in Table 7 fur-
ther characterized through:
Figure 33 - Physical layer of communication interface
?
?
?
?
?
?
There are no internal pull-up resistors
The SDA/SCL IOs are 3.3/5 V tolerant
Full SMBus clock speed of 100 kbps
Clock stretching limited to 1 ms
SCL low time-out of >25 ms with recovery
within 10 ms
Recognizes any time Start/Stop bus conditions
RX
TX
3.3/5V
R pull-up
SDA/SCL
The SMB_ALERT_L signal indicates that the power supply is experiencing a problem that the system agent should investi-
gate. This is a logical OR of the Shutdown and Warning events. The power supply responds to a read command on the gen-
eral SMB_ALERT_L call address 25(0x19) by sending its status register.
BCD.00040_AG Sep-11-2013
13
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PGB1040805NR
SUPPRESSOR ESD 24VDC 0805 SMD
PGB2010402KRHF
SUPPRESSOR ESD 12VDC 0402 SMD
PHW603616
BOX FIBER 63.5X36.5X18.1" GREY
PI-1902
BOX ABS 1.26" X 1.97" X 3.54"GRY
PI-1905
BOX ABS 1.97" X 2.36" X 4.72"GRY
PI-1908
BOX ABS 2.36" X 3.15" X 5.91"GRY
PI-1911
BOX ABS 3.15" X 3.94" X 7.48"GRY
PJ18168HP42
BOX FIBER 20.0X18.0X8.47" GREY
相关代理商/技术参数
PFE8KR100E
制造商:OHMITE 制造商全称:Ohmite Mfg. Co. 功能描述:Powr-Rib Edgewound Edgewound and Round Wire
PFEC2X2CL
功能描述:FITTING END CAP POLY CLR 2 X 2" RoHS:否 类别:线缆，导线 - 管理 >> 线槽，走线系统 - 附件 系列:- 标准包装:1 系列:PANDUCT® 附件类型:盖 - 线管 适用于相关产品:Panduit 导管 H 型 高度:- 宽:4"（101.6mm） 长度:36.0"（914.4mm） 颜色:黑 其它名称:298-HC4BL36
PFEC4X4CL
功能描述:FITTING END CAP POLY CLR 4 X 4" RoHS:否 类别:线缆，导线 - 管理 >> 线槽，走线系统 - 附件 系列:- 标准包装:1 系列:PANDUCT® 附件类型:盖 - 线管 适用于相关产品:Panduit 导管 H 型 高度:- 宽:4"（101.6mm） 长度:36.0"（914.4mm） 颜色:黑 其它名称:298-HC4BL36
PFEFAN01
制造商:FAIRFORD ELECTRONICS 功能描述:FAN PFE 1
PFEFAN02
制造商:FAIRFORD ELECTRONICS 功能描述:FAN PFE 2
PFEN57-16
制造商:Woodhead Molex 功能描述:
PFE-P
功能描述:线性和开关式电源 COVER FOR PFE RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度:
P-FEX-440
制造商:PSM International 功能描述: